Audi A3

since 1997 of release

Repair and car operation



Audi A3
+ Maintenance instruction
+ Current leaving and service
+ Engine
+ Systems of cooling, heating
+ the Power supply system and production of the fulfilled gases
+ engine Electric equipment
+ Manual box of gear shifting
+ Automatic transmission and models with a full drive
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   General information and security measures
   Care of a body
   Care of the panels of furnish made of vinyl
   Care of an upholstery and salon rugs
   Repair of insignificant damages of body panels
   Repair of considerable damages of a body
   Removal and installation of a vnutrisalonny mirror
   Removal and armrest installation
   Removal and installation of the bottom central console
   Removal and installation of the diagnostic tip of systems of safety
   Removal and installation of the central console
   Removal and installation of facing are resistant And
   Removal and pocket installation from the driver
   Removal and installation of a ware box
   Removal and installation of back lateral facing
   Removal and installation of facing of a back part of a roof
   Removal and installation of a level of a threshold
   Removal and installation of facing of a door of a back
   Removal and installation of facing of a luggage carrier
   Removal and installation of facing of the lock of a trunk lid
   Removal and installation of a forward seat
   Removal and installation of a cover of a forward seat
   Removal and installation of a cover directing seats from a channel
   Removal and installation of a cover directing seats from the tunnel
   Connection of a crossing point of conducting of a safety cushion
   Removal and installation of a back seat and back
   Removal and installation of the panel of the lock of a cowl
   Removal and installation of bumpers
   Removal and installation covered
   Removal and installation of an internal slip covered
   Removal and installation of loker of an arch of forward and back wheels
   Removal and installation of a cable of a drive of the lock of a cowl
   Removal and installation of the lock of a cowl
   Removal and installation of a hook of a cowl
   Removal, installation and cowl adjustment
   Cowl consolidations
   Removal and installation of a door of a back
   Removal and installation of a loop of a door of a back
   Adjustment of a door of a back
   Removal and installation of a sealant of a door of a back
   Removal and installation of the lock of a door of a back
   Removal and installation of the locking mechanism
   Removal and installation of a maple element of the lock of a door of a back
   Removal and installation of a level of the handle of a door of a back
   Removal and installation of facing of a door
   Isolation of a covering of a door
   Adjustment of the button of an unblocking
   Removal and installation of a forward door and holder of adjusting elements
   Door adjustment
   Removal and installation of a window regulator and glass of a window of a door
   Removal and installation of the electric motor of a window regulator
   Removal and installation of the handle of a forward door and lock cylinder
   Removal and installation of a beam of adjusting elements and loops of a back door
   Removal and installation of a guard and beam lateral amplifiers/levels of mine of a window
   Installation of a lateral safety cushion
   Installation of a lateral safety cushion in a beam of adjusting elements
   Removal and installation of an external mirror and mirror glass
   Removal and installation of a slip are resistant In
   Removal and installation of a lateral molding
   Removal and installation of an overlay of a door and wing
   The uniform lock - general information and vacuum hoses
   Removal and installation of activators of the uniform lock
   Emergency unblocking of a cover of the hatch of a fuel tank
   Removal and installation of the pump of the uniform lock
   Replacement of elastic bands of brushes of screen wipers
   Adjustment snuffled a stekloomyvatel
   Removal and installation snuffled a windscreen washer
   Removal and installation, check and adjustment of final position of levers of a screen wiper
+ Onboard electric equipment
+ Elektroskhema


38a8de3e

Removal and installation of a forward door and holder of adjusting elements

GENERAL INFORMATION

Forward door

1–holder
2–bolt, 30 N • m М8 x 26
3–bolt, 30 N • m М8 x 32
4–adjusting wedge. It should be always established
5–door. The door can be removed also without removal of the holder of adjusting elements
6–bolt, 30 N • m
7–adjusting wedge. It should be always established
8–guard of a lateral emphasis
9–drive cable
10-bolt, 30 N • m М8 x 26
11-lock draft

REMOVAL


ATTENTION

The door can be removed also without removal of the holder of adjusting elements. The holder in this case is not required to remove.


PERFORMANCE ORDER
1. Remove door facing, address to the subsection Removal and installation of facing of a door.
2. Remove facing of a rack And (below), address to the subsection Removal and installation of facing of a rack And.
3. Disconnect electric wires and a vacuum hose of the uniform lock from the holder–1–.
4. Disconnect a cable–9–from the holder.
5. Turn out bolts (2, 3, 6 and 10). Thus remove adjusting wedges–4–and–7–.
6. Take out up the holder of adjusting elements.
7. Remove a casing between a door and a rack And.
8. Remove the plug at a rack And.
9. Take out electric wires and a vacuum hose of the uniform lock from a rack And.
10. Disconnect electric wires and a vacuum hose at A.Otsoyedinite's rack the tip of a hose of the uniform lock, address to subsection the Uniform lock – general information and vacuum hoses.
11. Watch that the socket did not slide off in A.Zakrepite's rack it a clothespin.
12. Ask the assistant to support a door.
1–the bolt, is established from within, 30 N • to m
2–door loop the top
3–cover, 23 N • m
4–bolt, 30 N • m
5–Torx screw, 30 N • m
1–loop bottom
2–door forward
3–bolt, 30 N • m
4–Torx screw, 30 N • m
5–bolt, 30 N • m
13. Unscrew T45 Torx screws from a door at loops from above and from below.
14. Remove a door by means of the assistant.

INSTALLATION

PERFORMANCE ORDER
1. Establish a door by means of the assistant in loops and fix T45 Torx screws. Moment of an inhaling of 30 N • m.
2. Insert electric wires and a vacuum hose of the uniform lock into the socket of a rack And.
3. Insert electric wires and a vacuum hose into a rack And.
4. Fix plugs in a rack And.
5. Insert a casing between a door and a rack And.
6. Enter the holder from above into a door.
7. Fix the holder bolts. Do not forget about adjusting wedges of bolts–3–and–6–, address to an illustration. Sequence of an inhaling: (2, 10, 6, 3). Moment of an inhaling of 30 N • m. Adjustment of wedges is considered in subsection door Adjustment.
8. Connect a cable–9–to the holder.
9. Connect electric wires and a vacuum hose of the uniform lock, lay them and fix, address to subsection the Uniform lock – general information and vacuum hoses.
10. Adjust a door.
11. Establish facing of a rack And, address to the subsection Removal and installation of facing of a rack And.
12. Establish door facing, address to the subsection Removal and installation of facing of a door.