Audi A3

since 1997 of release

Repair and car operation

Replacement of lamps of external lighting

PERFORMANCE ORDER

1. Switch off the switch of the corresponding lamp.
2. Switch off ignition.

Near and far light

ATTENTION

Lamps Н7 are under pressure and can burst at performance of their replacement. Therefore at replacement of lamps Н7 it is necessary to use mittens and goggles.

PERFORMANCE ORDER

1. Open a cowl.
	2. Uncover behind a headlight. For this purpose press on both levels–1–down and disconnect them from holders–2–. Cast away a cover–3–above back and take out from the bottom directing.
	3. Rasstykuyte I will corrode lamps of a passing beam–3–or a driving beam–4–. 1–the electric motor of adjustment of range of light, 2 – I will corrode headlights.
4. Raise from a reverse side of a headlight a spring clip in the center a little and incline it in the arrow direction.
5. Rasstykuyte I will corrode lamps of a passing beam.
6. Press and open a spring clip over a lock pad.
7. Take out a lamp from a reflector. ATTENTION Do not take a lamp naked fingers. The print of fingers evaporates and besieged on a reflector, reducing a light stream of a lamp. Surely establish a lamp of the same execution. Spots on a lamp are eliminated with the pure scarf moistened in alcohol.
8. Insert a new lamp so that pads entered into the corresponding grooves on the case.
9. Cast away back a spring bracket and fix in pads.
10. Join the socket on the boss.
11. Put a cover on a reverse side of a headlight and fix a spring clip.
12. Check adjustment of headlights in conditions HUNDRED.
13. Close a cowl.

Parking light

PERFORMANCE ORDER

1. Open a cowl.
2. Uncover behind a headlight. For this purpose above press down both plastic levels and release them. Cast away a cover back.
	3. Take out a cartridge–1–with a lamp from a reflector. 2–tip of a driving beam.
4. Take out a lamp from the boss.
5. Insert into a cartridge a new lamp.
6. Press a cartridge with a lamp into a reflector against the stop.
7. Connect a cover on a reverse side of a headlight below and fix it above.
8. Close a cowl.

Forward index of turn

PERFORMANCE ORDER

1. Remove a forward signal of turn, address to the subsection Removal and installation of the forward index of turn.
	2. Turn to the left a cartridge of a lamp–1–and take out it from the case-3-.
3. Slightly press a lamp–2–into a cartridge, turn on 90 ° (1/4 turns) to the left and take out a lamp. ATTENTION Do not concern a flask of a new lamp hand fingers. Use a pure rag or put on thin gloves.
4. Insert a new lamp, slightly press on it and turn to the right.
5. Insert a cartridge with a lamp into a reflector and turn to the right. ATTENTION The boss should be fixed.
6. Establish the turn index, address to the subsection Removal and installation of the forward index of turn.

Lateral repeater of the index of turn

PERFORMANCE ORDER

	1. Press fingers the turn index forward in the headlight direction (an arrow illustrations) and take out it in a back part from an opening in a wing–3–. At removal the lamp is displaced forward, overcoming force of a plastic spring–4–.
2. Remove a cartridge of a lamp–5–from the case-6-.
3. Take out a lamp from the boss and replace.
4. Insert a cartridge with a lamp into the case.
5. Insert a lamp behind into plastic hooks in a wing opening, on the other hand press and fix a plastic spring.

Back lamp

PERFORMANCE ORDER

1. Open a back door.
2. Open a luggage carrier pocket at the left or on the right. For this purpose turn a clip above at a pocket cover on the left.
	3. Rasstykuyte I will corrode – 3–back lamps.
4. Compress lock levels–2–and thus release the holder of a lamp.
5. Take out the holder of a lamp–1–.
6. The damaged lamp slightly press into a cartridge, turn on 90 ° (1/4 turns) to the left and take out. ATTENTION Insert a new lamp, slightly press it and turn to the right.
7. Insert the holder of a lamp into a back lamp, press and fix.
8. Join the socket at the holder of a lamp.
9. Close a cover of a pocket of a luggage carrier and fix a clip turn to the right.
10. Close a back cover.

Lamp of illumination of registration plate

PERFORMANCE ORDER

1. Open a back door.
	2. Turn on in a level–1–on two screws with crosswise shlitsa–3–. On an illustration the lamp of illumination of the right registration plate is represented.
3. Take out the holder of a lamp from a level and расстыкуйте I will corrode – 2–.
4. Take out a lamp–4–of the boss and replace. Thus watch reliability of installation of a lamp. If necessary slightly turn in clips.
5. Join the socket.
6. Insert the holder of a lamp into a level and fix screws.
7. Close a back door.

Additional stoplight

The additional stoplight is located at the top of a back door behind back glass.

PERFORMANCE ORDER

1. Remove the top internal facing of a back door, address to the subsection Removal and installation of facing of a door of a back.
	2. Rasstykuyte I will corrode – 6–.
3. Turn out the fastening screw from–4–of a nasechny rivet–1–.
4. Disconnect a hook–7–of an aperture and remove a stoplight.
5. Remove a rasseivatel–3–from the holder of a lamp–2–.
6. Take out the damaged lamp–5–of the holder of a lamp–2–and insert a new lamp.
7. Insert the holder of a lamp with a rasseivatel and fix it screws.
8. Join the socket.
9. Establish into place internal facing of a back door, address to the subsection Removal and installation of facing of a door of a back.