Audi A3

since 1997 of release

Repair and car operation

Audi A3
+ Maintenance instruction
+ Current leaving and service
+ Engine
+ Systems of cooling, heating
+ the Power supply system and production of the fulfilled gases
+ engine Electric equipment
+ Manual box of gear shifting
+ Automatic transmission and models with a full drive
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
- Onboard electric equipment
   Electric equipment of system of comfort
   Diagnostics of malfunctions of onboard electric equipment - the general information
   Check of the electric motor of a screen wiper
   Check of warmed back glass
   Stoplight check
   Removal, installation and check of a sound signal
   Safety locks
   Fusible inserts - the general information
   Chain breakers (thermal relays)
   Relay
   Replacement of batteries of a key of remote control
   Replacement of a battery/lamp of a natural with illumination
   Anticreeping blocking
   Lighting devices
   Replacement of lamps of external lighting
   Replacement of bulbs of internal lighting
   Removal and headlight installation
   Removal and installation of the electric motor of adjustment of range of light
   Removal and installation of the forward index of turn
   Removal and installation of a back lamp
   Adjustment of light of headlights
   Devices
   Removal and installation of a control panel
   Removal and installation of the podrulevy switch
   Removal and installation of switches and lamps
   Removal, installation and radio receiver coding
   Input of a code of a radio receiver
   Removal and loudspeaker installation
   Removal and installation of the aerial of a roof
   Additional installation of a radio telephone on in a special way prepared models
   Removal and installation of the electric motor of a forward screen wiper
   Removal and installation of the lever and electric motor of a back screen wiper
   Removal and installation of a cleaner of back glass
   Removal and tank installation with the pump of a stekloomyvatel
   Elements темпостата
+ Elektroskhema

Removal and installation of the podrulevy switch

GENERAL INFORMATION

Into structure of the podrulevy switch enter: both switches of the index of turns / driving beam and screen wiper.

REMOVAL

PERFORMANCE ORDER

1. Disconnect a negative cable (–) the storage battery at the switched-off ignition. ATTENTION Thereof information from electronic blocks of memory, as, for example, a radio receiver code is erased. Without a code the radio receiver can be included only by the manufacturer or HUNDRED AUDIS. Therefore familiarize with subsection materials Input of a code of a radio receiver. Read surely remarks on security measures when using a safety cushion, thus address to the subsection Steering.
2. Remove the safety cushion block from the driver, thus address to the subsection Removal and installation of the block of a safety cushion.
3. Remove a steering wheel, thus address to the subsection Removal and installation of a steering wheel.
	4. Disconnect the handle of the mechanism of adjustment of a steering column-1-.
5. Turn out 2 screws with a crosswise shliyets – 4–and the screw with an internal shestigrannik – 2–(a key of 4 mm).
6. Turn out 2 screws of fastening by-3-thin long screw-driver.
7. Remove the top and bottom parts facing of the podrulevy switch.
	8. Rasstykuyte I will corrode – 1–.
9. Unscrew the screw with an internal shestigrannik – 2–(5 mm) so that podrulevy the switch could move slightly.
10. Carefully disconnect electric connections from the podrulevy switch. ATTENTION At removal of the podrulevy switch the spring remains on the switch. Watch that the spring was not braided and remained in the average situation.
11. Remove podrulevy the switch from a column and put aside.

INSTALLATION

PERFORMANCE ORDER

	1. Put on podrulevy the switch-2-a steering column, without fixing it.
2. Put on a steering wheel.
3. Fix at first podrulevy the switch-2-the screw with an internal shestigrannik – 3–on a steering column so that the distance to a steering wheel made and = 3 mm.
4. Again remove a steering wheel and execute further installation in sequence, return to removal.
5. Establish a steering wheel, address to the subsection Removal and installation of a steering wheel.
6. Establish a safety cushion, address to the subsection Removal and installation of the block of a safety cushion.
7. Attach a weight cable (–) the storage battery. Attention: Make active high-rise automatic equipment of an electric window regulator, and also establish hours and enter a radio tape recorder code, address to subsection Input of a code of a radio receiver.